# Inspection checklist by product: free, printable

> Free pre-shipment inspection checklist for ten product categories: critical, major and minor defects, on-site tests, measurements, packing and marks. Save as PDF.

Source: https://sourcesquid.co/check/inspection-checklist/

Free check · Inspection checklist

# The inspection checklist for your product.

An inspection checklist lists what the inspector checks on every unit in the sample: defects classed as critical, major or minor, on-site tests, measurements, packing and market marks. Pick your category to see the full list, free, then save it as a PDF.

Open the checklist [See an example report](https://sourcesquid.co/quality/sample-report/)

10
    product categories

330
    checkpoints in all

Free
    on screen, PDF or email

Checklist · Apparel and textilesZ1.4 · Level II

**Critical defects** Broken needle, needle fragment or other metal left in the garment

 _5_

**Major defects** Hole, cut or tear; open, broken or skipped stitches on a seam

 _7_

**Minor defects** Untrimmed thread ends

 _6_

**6** on-site tests**6** measurements**7** packing checks

Ten categories · free

## Pick a category. Get every checkpoint.

ApparelHome textilesMetal hardgoodsPlastic productsElectronicsFurnitureLeather and footwearCeramics and glassToysPackaging

[Book this inspection: from USD 249 per person-day](https://sourcesquid.co/book/?service=pre-shipment-inspection&product=Apparel%20and%20textiles) [WhatsApp us](https://wa.me/919840698791?text=Hello%20SourceSquid%2C%20I%20would%20like%20to%20book%20an%20inspection%20for%20apparel%20and%20textiles.)

Inspection checklist

### Apparel and textiles

T-shirts, shirts, dresses, knitwear, denim, outerwear, sportswear, childrenswear and fabrics by the metre.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 suits most apparel. Premium lines often tighten major to 1.5.

#### Critical defectsAQL 0: none allowed

  * Broken needle, needle fragment or other metal left in the garment
  * Sharp edge or point on a button, rivet, zip or trim
  * Children’s wear: cords or drawstrings at the hood or neck outside EN 14682 (EU and UK) or 16 CFR 1120 (US)
  * Children’s wear: button, snap or trim that comes off in the pull test
  * Mould, or live insects in the garment or carton

#### Major defectsAQL 2.5 typical

  * Hole, cut or tear; open, broken or skipped stitches on a seam
  * Measurement outside tolerance at a key point: chest, length, waist, hip or inseam
  * Shade difference between panels of one garment, or against the approved colour
  * Wrong or missing size, care or fibre composition label
  * Zip that does not run; button or snap missing or not closing
  * Stain or oil mark in a prominent area (zone A: front and upper body)
  * Stripes or checks mismatched at the front; twisted leg or body

#### Minor defectsAQL 4.0 typical

  * Untrimmed thread ends
  * Slightly uneven stitch density or light puckering away from the front
  * Small mark in a less visible area that cleans off
  * Pressing creases or shine
  * Label slightly off position but fully legible
  * Small slub or knot in the fabric in a hidden area

#### On-site tests

  1. **Seam strength pull test** Stress seams (crotch, armhole, side seam) pulled at the force in your specification.
  2. **Colour fastness to rubbing** Dry and wet white cloth rubbed on dark shades and graded against the grey scale.
  3. **Fabric weight (GSM)** Round cutter and scale, compared with the fabric specification.
  4. **Button and snap pull test** Pull gauge on children’s wear at the value in your specification or standard.
  5. **Fit check** Base size on a dress form or fit model, where agreed.
  6. **Barcode scan** Hangtag and polybag barcodes decode and match the SKU and size.

#### Measurements unit: cm

Point| How| Reading  
---|---|---  
Chest width| 1 cm below the armhole, laid flat|   
Body length| From the high point shoulder|   
Sleeve length| Shoulder point to cuff edge|   
Waist and hip| Relaxed, laid flat|   
Inseam| Crotch point to hem (trousers)|   
Neck opening| Stretched and relaxed, knits|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Folded to the folding instructions, with tissue, clips and inserts as specified
  * Size stickers on polybags match the garment inside
  * Polybags carry a suffocation warning where required
  * Solid or mixed assortment matches the packing list by size and colour
  * Hanging garments: hangers, sizers and covers as specified
  * Cartons dry, sealed, marked and within the weight limit
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    Fibre composition with the names in Regulation (EU) 1007/2011; care symbols to ISO 3758 are standard practice.

UK
    Fibre composition under the Textile Products (Labelling and Fibre Composition) Regulations 2012.

US
    Fibre content, country of origin and maker identity (name or RN) under the Textile Act; permanent care label under the FTC Care Labeling Rule.

Australia
    Permanent care label under the care labelling information standard.

Children’s wear
    Cords and drawstrings: EN 14682 in the EU and UK; 16 CFR 1120 in the US.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We check the order is finished and at least 80% packed, draw cartons at random, then inspect every garment in the sample on a lit table against the approved sample and your size spec. Stress tests and measurements use separate units so the sample stays saleable.

SourceSquid · sourcesquid.co/quality/checkpoints/apparel-and-textiles/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Home textiles

Bed linen, duvets and pillows, towels, cushions, throws, curtains, table linen and rugs.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 is the usual starting point for home textiles.

#### Critical defectsAQL 0: none allowed

  * Needle fragment or other metal in the product
  * Mould, live insects or foreign matter in fillings
  * Curtains and blinds: accessible looped cords without the safety device the market’s standard requires (e.g. EN 13120)
  * Children’s bedding: detachable small parts, or loose cords and ties

#### Major defectsAQL 2.5 typical

  * Size outside tolerance, or fitted sheet pocket too shallow for the stated mattress depth
  * Hole, tear, open seam or broken stitching
  * Shade variation within a set, or against the approved colour
  * Print misregistration, bleeding or missing colour
  * Towels: pulled loops, uneven pile or frayed selvedge
  * Rugs: loose tufts, uneven pile height or backing that separates
  * Missing, wrong or illegible labels; incomplete set

#### Minor defectsAQL 4.0 typical

  * Untrimmed thread ends
  * Slightly uneven hem width
  * Small slub or mark away from the face side
  * Packing creases
  * Label slightly off position

#### On-site tests

  1. **Fabric weight (GSM)** Round cutter and scale; towels also weighed per piece.
  2. **Colour fastness to rubbing** Dry and wet white cloth on dark and printed fabrics.
  3. **Towel absorbency** Water drop test: the drop should soak in quickly and evenly.
  4. **Seam slippage** Hand check at stress points on covers and cushions.
  5. **Closure check** Zips, buttons and envelope openings on covers work smoothly.
  6. **Fit check** Fitted sheets on a mattress or frame of the stated size and depth.

#### Measurements unit: cm

Point| How| Reading  
---|---|---  
Length and width| Laid flat without tension|   
Pocket depth| Fitted sheets, at each corner|   
Hem and border width| At several points per piece|   
Flap depth| Pillowcases and duvet covers|   
Pile height| Rugs and towels, where specified|   
Weight per piece| Towels, throws and fillings (g)|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Sets complete: cover, sheets and pillowcases as listed
  * Folding, insert card and retail bag or box as the approved sample
  * Bags carry a suffocation warning where required
  * Barcode and size on the pack match the product
  * Rugs rolled or folded as instructed, wrapped and labelled
  * Cartons dry, sealed, marked and within the weight limit
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    Fibre composition under Regulation (EU) 1007/2011.

UK
    Fibre composition under the Textile Products (Labelling and Fibre Composition) Regulations 2012.

US
    Fibre content, country of origin and maker identity under the Textile Act; stuffed-article law labels where state rules require them.

Australia
    Permanent care label under the care labelling information standard.

Eco claims
    OEKO-TEX or organic labels only where a valid certificate covers the product.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We count sets and cartons, then open sampled units fully: sheets are unfolded and measured, towels weighed, covers zipped and unzipped, rugs unrolled on a clean floor. Colour is compared with the approved sample in a light box.

SourceSquid · sourcesquid.co/quality/checkpoints/home-textiles/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Metal hardgoods

Kitchenware and drinkware, hardware and fittings, tools, fasteners, brackets, castings and sheet-metal parts.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 is typical. Engineering parts often add a separate plan for critical dimensions.

#### Critical defectsAQL 0: none allowed

  * Sharp edge or burr on a surface the user handles
  * Wrong alloy where safety or food contact depends on it (e.g. 201 in place of 304 stainless steel)
  * Crack in a weld or casting on a load-bearing part
  * Missing mandatory warning or safety instruction

#### Major defectsAQL 2.5 typical

  * Dent or deformation visible in normal use
  * Plating or coating peeling, blistering or with bare spots; rust or corrosion
  * Dimension outside tolerance that affects fit or assembly
  * Damaged threads; fastener does not engage fully
  * Leak on a container or vessel
  * Hinge, lid or lock binding or not closing
  * Weld porosity or spatter on a visible surface

#### Minor defectsAQL 4.0 typical

  * Light scratch on a secondary surface
  * Small polishing or tool mark
  * Slight colour variation within the approved range
  * Logo print slightly off position

#### On-site tests

  1. **Alloy check (XRF)** Handheld analyser confirms the grade, for example 304 against 201 stainless steel.
  2. **Coating thickness** Gauge reading in µm on plated or painted surfaces against the specification.
  3. **Cross-hatch adhesion** Paint or powder coat cut and taped to ISO 2409 or ASTM D3359.
  4. **Thread check** Go/no-go gauges on tapped holes and threaded parts.
  5. **Leak test** Containers filled with water, closed and inverted for the time in your specification.
  6. **Function and fit** Lids, hinges and locks cycled; parts assembled with their mating parts.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Overall length, width, height| Calipers or tape against the drawing|   
Diameter| Outer and inner, at the points on the drawing|   
Wall or sheet thickness| Micrometer or ultrasonic gauge|   
Hole size and position| Pin gauges and calipers|   
Flatness or straightness| Feeler gauge on a surface plate, where specified|   
Weight| Scale, in grams|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Anti-rust protection as specified: VCI paper, oil or sealed bags with desiccant
  * Individual sleeves or dividers so parts do not touch and scratch
  * Inner and master cartons strong enough for the weight
  * Count per bag and per carton matches the packing list
  * Retail packaging and inserts match the approved artwork
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    Food-contact items: glass-and-fork symbol or “for food contact” wording where food use is not obvious (Regulation (EC) 1935/2004).

EU and UK
    Nickel release limits for parts in direct and prolonged skin contact (REACH Annex XVII, entry 27).

EU (CBAM)
    Iron, steel and aluminium goods need emissions data from the producer for the importer’s CBAM declaration.

US
    Country of origin marked on the article or its container; California Proposition 65 warning where a listed substance is present.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We inspect in good light against the golden sample, run the XRF and gauge checks on units drawn from different cartons, and photograph every defect next to a scale rule. Leak and function tests run on a separate set of units.

SourceSquid · sourcesquid.co/quality/checkpoints/metal-hardgoods/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Plastic products

Housings and covers, food containers and kitchenware, bottles, garden and household products, and technical parts.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 suits most consumer plastics. Technical parts add a dimensional plan per cavity.

#### Critical defectsAQL 0: none allowed

  * Sharp flash or broken edge that could cut
  * Children’s products: small part that detaches
  * Food-contact item in a resin not covered by the compliance documents
  * Crack in a part that carries load or pressure

#### Major defectsAQL 2.5 typical

  * Short shot: part not fully formed
  * Flash on a visible or mating edge
  * Sink marks or warpage that show on the face or affect fit
  * Stress whitening or cracks
  * Colour outside the approved range; black specks or contamination
  * Snap fit, hinge or thread that does not engage; lid that does not seal
  * Critical fit dimension outside tolerance

#### Minor defectsAQL 4.0 typical

  * Gate mark not trimmed fully flush on a hidden face
  * Light flow lines on a non-visible surface
  * Slight gloss variation
  * Small scuff from handling

#### On-site tests

  1. **Leak or seal test** Containers and lids filled with water or pressurised, then inverted.
  2. **Drop test** Product dropped from the height in your specification, then checked for cracks.
  3. **Snap-fit and hinge cycles** Opened and closed the number of times in your specification.
  4. **Colour check** Against the approved master in a light box under D65 daylight.
  5. **Assembly check** Parts fitted to their mating parts without force.
  6. **Weight check** Part weight against the standard: a light part can point to a short shot or a material change.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Overall length, width, height| Calipers against the drawing|   
Wall thickness| At the points on the drawing|   
Critical fit dimension| Per cavity, where the mould has several|   
Thread or neck finish| Gauges for bottles and closures|   
Flatness or warp| Feeler gauge on a surface plate|   
Weight| Scale, in grams|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Protective film or bags so faces do not scratch
  * Stacking that does not deform parts in the carton
  * Cavity number legible and recorded for traceability
  * Count per bag and per carton matches the packing list
  * Retail packaging matches the approved artwork
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    Food-contact plastics: written declaration of compliance and migration testing under Regulation (EU) 10/2011.

EU and UK
    REACH: suppliers must inform you if an article contains a candidate-list substance above 0.1% by weight.

Material mark
    Material code to ISO 11469 (for example >PP<) or a resin identification code, as specified.

US
    Food-contact resins that meet FDA rules (21 CFR 174–178); Proposition 65 warning where a listed substance is present.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We note the mould and cavity numbers, draw samples across cartons so every cavity is represented, and inspect under good light at arm’s length. Colour is judged in a light box, and fit and seal tests run on separate units.

SourceSquid · sourcesquid.co/quality/checkpoints/plastic-products/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Electronics and electricals

Small appliances, chargers and power supplies, lighting, audio, wearables, battery-powered devices and accessories.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 is common. Safety tests often run on every sampled unit or a special-level plan.

#### Critical defectsAQL 0: none allowed

  * Hi-pot (dielectric strength) failure
  * Earth continuity failure on a Class I product
  * Exposed live parts or damaged insulation
  * Plug that does not match the market standard
  * Battery swelling, leaking or overheating

#### Major defectsAQL 2.5 typical

  * Function failure: power, a button, mode, display or indicator
  * Charging failure or run time below specification
  * Wireless pairing or range failure
  * Rating label wrong, missing or not durable
  * CE, UKCA, FCC or WEEE marking missing where required
  * Crack or gap in the housing; dead pixels beyond specification
  * Missing accessory or manual

#### Minor defectsAQL 4.0 typical

  * Light scratch on the housing
  * Slightly uneven gap between housing parts
  * Print slightly off position
  * Dust under a protective film

#### On-site tests

  1. **Hi-pot test** Dielectric strength at the voltage and time of the product standard (e.g. IEC 60335-1 or IEC 62368-1).
  2. **Earth continuity** Resistance between the earth pin and exposed metal on Class I products.
  3. **Input power** Power and current at rated voltage against the rating label.
  4. **Full function test** Every button, mode, indicator and display, plus charging and pairing.
  5. **Internal check** One unit opened: wiring, soldering, insulation and key components against the approved construction.
  6. **Cord pull** Strain relief holds the cord under a firm pull.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Overall length, width, height| Calipers against the specification|   
Cable length| Plug to product, in metres|   
Plug pin dimensions| Where the plug is part of the product|   
Button travel and fit| Against the golden sample|   
Weight| Scale, in grams|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * All accessories, cables and manuals in each box
  * Foam or pulp inserts hold the product without movement
  * Circuit boards and spares in antistatic bags
  * Gift box artwork, barcodes and model number match the product
  * Lithium battery handling marks on cartons where the shipping rules require them
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    CE marking with a Declaration of Conformity covering LVD, EMC, RoHS and RED as applicable; crossed-out wheelie bin (WEEE).

UK
    UKCA or CE as the UK rules allow; WEEE mark.

US
    FCC Part 15 authorisation for devices with digital or radio circuits; NRTL listing (such as UL or ETL) where your retailer requires it.

Australia and NZ
    RCM mark, with registration on the EESS database for in-scope electrical equipment.

Plugs
    BS 1363 (UK), CEE 7 (EU), NEMA 1-15 or 5-15 (US), AS/NZS 3112 (Australia and NZ).

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We bring calibrated hi-pot and earth testers, run the safety tests first, then the full function test, then the cosmetic check. One unit is opened and compared with the approved construction so component changes are caught early.

SourceSquid · sourcesquid.co/quality/checkpoints/electronics/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Furniture

Case goods and storage, tables, dining and upholstered seating, office chairs, outdoor furniture and flat-pack.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 is usual. For large items, many buyers use a special level to keep the sample practical.

#### Critical defectsAQL 0: none allowed

  * Storage unit that tips over, or is missing required anti-tip hardware or warnings
  * Structural crack or joint failure under load
  * Protruding screw, staple or sharp edge
  * Finger trap in a folding, reclining or moving mechanism
  * Live insect activity in wood (fresh frass or bore dust)

#### Major defectsAQL 2.5 typical

  * Loose joint or wobble on a flat floor
  * Finish defect in view: runs, orange peel, sanding marks or colour mismatch
  * Crack or split in solid wood
  * Wrong or missing hardware; trial assembly fails
  * Drawers or doors misaligned, sticking or not closing flush
  * Upholstery stain, tear or crooked seam
  * Dimension outside tolerance

#### Minor defectsAQL 4.0 typical

  * Small sanding mark on a hidden surface
  * Slight colour variation within the approved range
  * Small glue residue on a hidden joint
  * Light scuff on the underside

#### On-site tests

  1. **Trial assembly** Assembled from the packed carton using only the manual and hardware bag.
  2. **Moisture content** Pin meter on solid wood (commonly 8–12% for indoor furniture; follow your specification).
  3. **Load test** Seats, shelves and tops loaded at the value in your specification.
  4. **Stability and tip-over** Storage units checked to your market’s requirement, for example the US STURDY Act for clothing storage units.
  5. **Finish adhesion** Cross-hatch test on painted or lacquered surfaces.
  6. **Drawer and door cycles** Opened and closed repeatedly; runners and hinges checked.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Width, depth, height| Overall, against the drawing|   
Seat or top height| From the floor|   
Diagonals| Squareness of frames and carcasses|   
Drawer inner size| Width, depth and height|   
Level| All feet touch a flat floor|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Corner and edge protectors; foam or pulp where parts touch
  * Hardware bag sealed, counted and fixed in the carton
  * Assembly instructions inside, in the destination languages
  * Flat-pack parts labelled to match the instructions
  * Carton board grade suits the weight; weight label on heavy cartons
  * Carton drop test on one packed unit for flat-pack
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

US
    STURDY Act stability and warning label for clothing storage units; TSCA Title VI label for composite wood; TB 117-2013 label for upholstered furniture sold in California.

UK
    Display and permanent labels for upholstered furniture under the Furniture and Furnishings (Fire) (Safety) Regulations 1988.

EU
    Wood furniture falls under the EUDR, which applies from 30 December 2026 for large and medium operators.

Standards
    Test reports to the standards in your specification, for example EN 12520, EN 14749 or BIFMA.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We open cartons from different pallets, run a full trial assembly with the packed hardware, and inspect every surface in good light. Moisture readings, load and stability checks run on assembled units, which we photograph from every side.

SourceSquid · sourcesquid.co/quality/checkpoints/furniture/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Leather goods and footwear

Bags, wallets and small leather goods, belts, gloves, and leather, textile and synthetic footwear.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 is usual. Luxury lines often tighten major to 1.5.

#### Critical defectsAQL 0: none allowed

  * Needle fragment or tack left in a shoe or bag
  * Sharp edge on hardware
  * Mould on leather, lining or packing
  * Children’s footwear: small part that detaches

#### Major defectsAQL 2.5 typical

  * Sole bonding gap or delamination
  * Pair mismatched in size, shade, height or shape
  * Scar, cut or colour patch on a visible panel beyond the agreed grade
  * Skipped or broken stitches; thread ends not secured
  * Edge paint cracked or peeling
  * Zip, buckle, clasp or magnet not working; hardware plating peeling
  * Handle or strap loose; heel loose

#### Minor defectsAQL 4.0 typical

  * Glue mark that cleans off
  * Slight colour variation in a hidden area
  * Untrimmed thread ends
  * Small unevenness in edge paint

#### On-site tests

  1. **Sole bond flex** Shoes flexed by hand to show any gap between sole and upper.
  2. **Rub fastness** Dry and wet white cloth on the leather surface and edges.
  3. **Handle and strap pull** Pulled at the load in your specification.
  4. **Moisture reading** Leather moisture meter; silica gel checked in the pack.
  5. **Hardware cycles** Zips, buckles and clasps opened and closed repeatedly.
  6. **Odour check** Strong solvent or mould odour recorded.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Length, width, height| Bags and small leather goods|   
Handle drop and strap length| Adjustable straps at both ends|   
Leather thickness| Thickness gauge at several panels|   
Insole length| Footwear, per size|   
Heel and shaft height| Footwear, per size|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Pairs are left and right of the same size, in the right box
  * Paper stuffing, tissue and dust bags as specified
  * Silica gel in each box or bag
  * Box labels match the size, colour and style inside
  * Cartons dry, sealed and marked
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU and UK
    Footwear material labels for upper, lining and outer sole (Directive 94/11/EC).

EU and UK
    Chromium VI in leather in contact with skin below 3 mg/kg (REACH Annex XVII, entry 47); azo dye limits (entry 43).

US
    Country of origin marking; leather claims that follow the FTC leather guides (16 CFR 24); Proposition 65 warning where required.

Care
    Care instructions where supplied match the material.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We inspect each sampled piece on a clean, lit table, checking every panel, seam and edge against the approved sample and the agreed leather grade. Shoes are checked as pairs, flexed and measured per size.

SourceSquid · sourcesquid.co/quality/checkpoints/leather-goods-and-footwear/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Ceramics and glass

Stoneware, porcelain and earthenware tableware, mugs, bakeware, vases and decorative pieces, and glassware.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 is usual. Sets are counted as one unit or per piece, as you prefer.

#### Critical defectsAQL 0: none allowed

  * Chip or crack on a rim or edge that touches the mouth or hand
  * Glass shards or broken pieces in the pack
  * Breakage in the thermal shock test on an item sold as oven or dishwasher safe
  * Food-contact item without a passing lead and cadmium release report

#### Major defectsAQL 2.5 typical

  * Hairline crack found in the ring test
  * Crazing, pinholes or bare spots in the glaze on a food-contact surface
  * Decoration misaligned, smudged or missing
  * Warped base that rocks on a flat surface
  * Lid that does not fit; spout that drips
  * Capacity outside tolerance
  * Bubbles or stones in glass in a visible area

#### Minor defectsAQL 4.0 typical

  * Small glaze drip on the foot ring
  * Slight colour variation within the set
  * Small decoration spot away from view
  * Tiny bubble in a non-visible area

#### On-site tests

  1. **Ring (tap) test** Each sampled piece tapped: a dull sound points to a hidden crack.
  2. **Thermal shock** Hot and cold water cycles to your specification for oven or dishwasher-safe claims.
  3. **Capacity** Filled with water to the brim or to the fill line and measured.
  4. **Decoration adhesion** Tape and rub test on decals and prints.
  5. **Rock test** Base checked on a flat glass plate.
  6. **Pour and lid fit** Teapots, jugs and jars poured and closed.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Height and diameter| Calipers at rim and base|   
Capacity| Water fill, in ml|   
Wall thickness| At the rim and body|   
Lid fit gap| Feeler gauge where specified|   
Weight| Scale, in grams|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Each piece wrapped or separated by dividers
  * Set count per box matches the listing
  * Inner boxes fit tightly in the master carton
  * Carton drop test on one packed unit
  * Fragile and this-way-up marks on cartons
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    Lead and cadmium release limits for food-contact ceramics (Directive 84/500/EEC); glass-and-fork symbol where food use is not obvious.

US
    FDA limits on lead in ceramicware; decorative ware that looks like tableware marked “Not for food use” (21 CFR 109.16); Proposition 65 in California.

Claims
    Dishwasher, microwave and oven-safe marks match the test evidence.

Backstamp
    Backstamp or marking as specified.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We unpack sampled cartons fully, ring-test every sampled piece, and inspect glaze and decoration under good light. Capacity, thermal shock and rock tests run on separate pieces, and a packed carton is drop-tested before loading.

SourceSquid · sourcesquid.co/quality/checkpoints/ceramics-and-glass/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Toys

Plush and soft toys, plastic and wooden toys, battery-operated and ride-on toys, games and puzzles, and baby toys.

Suggested plan**AQL 0 / 1.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=1.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Toy buyers often use AQL 0 / 1.5 / 4.0 at Level II, with safety checks on extra units.

#### Critical defectsAQL 0: none allowed

  * Small part that fits the small parts cylinder, on a toy for children under 36 months
  * Sharp edge or sharp point on an accessible part
  * Eye, nose or small component that comes off in the torque and tension test
  * Button or coin battery accessible without a tool
  * Cord or string longer than the standard allows; finger trap in a moving part
  * Missing required age warning

#### Major defectsAQL 1.5 typical

  * Toy does not work as described: mechanism, sound, light or wheels
  * Seam opening on a soft toy; loose stuffing
  * Paint or print flaking
  * Missing part or accessory
  * Wrong or incomplete labelling or instructions
  * Retail box artwork does not match the approved proof

#### Minor defectsAQL 4.0 typical

  * Slight paint overspray
  * Untrimmed thread on a soft toy
  * Print slightly off position on the box
  * Small scuff on the packaging

#### On-site tests

  1. **Small parts cylinder** Toys for under 36 months: no part fits wholly in the cylinder (EN 71-1; 16 CFR 1501).
  2. **Torque and tension** Eyes, noses and small components at the EN 71-1 or ASTM F963 values for the age group.
  3. **Drop and abuse** Dropped and stressed for the age group, then small parts and sharp edges checked again.
  4. **Sharp edge and point** Checked by hand and with testers (EN 71-1; 16 CFR 1500.48 and 1500.49).
  5. **Seam strength** Soft toy seams pulled at the value in your specification.
  6. **Battery compartment** Opens only with a tool where EN 62115 or ASTM F963 requires it.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Overall length, width, height| Against the specification|   
Cord or string length| Fully extended|   
Smallest detachable part| Before and after abuse tests|   
Openings and gaps| Where fingers could enter|   
Weight| Scale, in grams|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Age grading and warnings on the retail pack as required
  * Plastic bags meet the film thickness or warning rules of the market
  * Assortment and count per carton match the packing list
  * Batteries packed as specified, with contacts protected
  * Cartons dry, sealed and marked
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    CE mark, EN 71 series, warnings in local languages, manufacturer and importer details, and a type or batch number.

UK
    UKCA or CE mark, with the UK importer’s details.

US
    ASTM F963 and CPSIA testing, a Children’s Product Certificate, CPSIA tracking label and small parts warning where required (16 CFR 1500.19).

Australia
    Mandatory standards for toys for children up to 36 months and for products containing button or coin batteries.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We run the safety checks on units separate from the visual sample so every result is clear. Our inspectors carry a small parts cylinder, torque and tension gauges and edge and point testers, and repeat the checks after the drop and abuse tests.

SourceSquid · sourcesquid.co/quality/checkpoints/toys/ · Your specification and approved sample decide the final class of any defect.

Inspection checklist

### Packaging

Corrugated shipping cartons, folding cartons, rigid gift boxes, labels and sleeves, mailers, bags and inserts.

Suggested plan**AQL 0 / 2.5 / 4.0** ANSI/ASQ Z1.4, Level II[Sample size for your lot →](https://sourcesquid.co/tools/aql-sampling-planner/?lot=3500&level=II&crit=0&major=2.5&minor=4.0)

Supplier
    

Order / PO
    

Lot size
    

Date
    

Level II with AQL 0 / 2.5 / 4.0 is usual; count packaging by the piece.

#### Critical defectsAQL 0: none allowed

  * Barcode that scans as a different product
  * Missing or wrong mandatory warning or legal text
  * Mould, oil or pests on a food-contact surface
  * Food-contact packaging with no compliance declaration

#### Major defectsAQL 2.5 typical

  * Print colour outside the tolerance agreed against the proof
  * Misregistration or text error visible to the customer
  * Wrong size or dieline: the product does not fit
  * Board below specification: wrong flute, ply or grammage
  * Glue flap not bonded; lamination bubbles or peeling
  * Barcode below the grade your customer requires

#### Minor defectsAQL 4.0 typical

  * Small ink spot or scuff
  * Slight crease mark away from the main panel
  * Small variation in varnish sheen

#### On-site tests

  1. **Board check** Flute, ply, grammage and caliper against the specification.
  2. **Compression strength** Supplier ECT or BCT report confirmed for the carton grade.
  3. **Rub (scuff) test** Print rubbed to check ink and varnish hold.
  4. **Glue bond** Glued seams opened by hand: fibre tear shows a good bond.
  5. **Barcode grade** Verifier reading to ISO/IEC 15416 where a grade is required.
  6. **Pack test** Product packed and drop-tested (ISTA 1A style) where the packaging is new.

#### Measurements unit: mm

Point| How| Reading  
---|---|---  
Internal length, width, height| Against the dieline|   
Board caliper| Thickness gauge|   
Print position| Distance of key elements from edges|   
Label size| Labels and sleeves|   
  
At least five units per size or version, against your specification and tolerances.

#### Packing and labelling

  * Packed flat or nested as instructed, banded in counted bundles
  * Protected from moisture: wrapped pallets, dry storage
  * Bundle and pallet counts match the packing list
  * Pallet labels and carton marks as specified
  * Shipping marks, carton count, gross weight and dimensions agree with the packing list

#### Market marks

EU
    PPWR applies from 12 August 2026: EU declaration of conformity and technical documentation, the importer’s name and postal address on the packaging, and lead, cadmium, mercury and hexavalent chromium together below 100 mg/kg.

EU food contact
    From 12 August 2026, PFAS limits apply to food-contact packaging under PPWR.

EU (later)
    Harmonised sorting labels become mandatory from 12 August 2028 at the earliest.

FSC
    FSC label printed only where the supplier holds a valid licence and chain-of-custody certificate.

Your compliance team or test lab confirms which rules apply to your exact product.

**How we inspect it.** We compare sampled pieces with the approved proof and dieline under D65 light, measure board and dimensions, and test glue bonds and print. Where the packaging is new, we pack your product into it and run a drop test.

SourceSquid · sourcesquid.co/quality/checkpoints/packaging/ · Your specification and approved sample decide the final class of any defect.

[ Example report**See what the inspection report looks like** Summary, photos of every defect, measurements and tests, page by page. ](https://sourcesquid.co/quality/sample-report/) Included when you book**Have a principal tailor this checklist to your spec and golden sample** Agreed with you before the inspector arrives. Included when you book an inspection.

Book the inspection

## This checklist, run at the factory.

Our own inspectors in India and China work through the checklist on a random sample drawn to ANSI/ASQ Z1.4, with a photo report within 24 hours.

  * from USD 249 per person-day, travel included within main clusters **Pre-shipment, in-line or loading inspection**

A principal tailors this checklist to your specification and golden sample, included in the booking, and confirms the inspector and the date.

[Book this inspection](https://sourcesquid.co/book/?service=pre-shipment-inspection&product=Apparel%20and%20textiles) [WhatsApp us](https://wa.me/919840698791?text=Hello%20SourceSquid%2C%20I%20would%20like%20to%20book%20an%20inspection%20and%20have%20the%20checklist%20tailored%20to%20my%20product.) [How inspections work](https://sourcesquid.co/quality/)

You see the exact total before you confirm. Pay by card, or ask for an invoice. Outside the main clusters, travel is confirmed before you pay.

Plan your inspection

## Free tools that work with this list.

[Sampling**AQL sampling planner** Sample size and accept numbers for your lot.](https://sourcesquid.co/tools/aql-sampling-planner/)[Form**Inspection checklist generator** An inspector’s form with blanks for every reading.](https://sourcesquid.co/tools/inspection-checklist/)[Testing**Test advisor** Which lab tests your product needs, and when.](https://sourcesquid.co/tools/test-advisor/)[Guide**Pre-shipment inspection checklist** How to plan and read a pre-shipment inspection.](https://sourcesquid.co/intelligence/pre-shipment-inspection-checklist/)

Checklist questions

## Straight answers.

Anything else, ask us directly. A principal replies, not a bot.

[anirudh@sourcesquid.co](mailto:anirudh@sourcesquid.co)

### What should a pre-shipment inspection checklist include?

The defects to look for, each classed as critical, major or minor; the on-site tests; the measurement points and tolerances; packing, labelling and carton checks; and the marks your market requires. Add your own specification and approved sample, which decide the final class of any defect.

### Can I use this checklist with my own inspector or the factory’s QC?

Yes. Save it as a PDF and send it with your specification and golden sample photos. It works as a common list for anyone checking the goods.

### Which AQL should I use?

Most consumer goods use ANSI/ASQ Z1.4 General Inspection Level II with AQL 0 for critical, 2.5 for major and 4.0 for minor defects. Each category below shows the usual plan; the AQL sampling planner gives the sample size for your lot.

### Can you tailor the checklist to my product?

Yes. When you book an inspection, a principal tailors the checklist to your specification and golden sample at no extra charge, and agrees it with you before the inspector arrives.

### How much does an inspection cost?

Inspections start at USD 249 per person-day, with travel included within our main clusters in India and China. You see the exact total before you confirm.
