SOURCESQUID®
EN
Free teardown
Free check · Inspection checklist

The inspection checklist for your product.

An inspection checklist lists what the inspector checks on every unit in the sample: defects classed as critical, major or minor, on-site tests, measurements, packing and market marks. Pick your category to see the full list, free, then save it as a PDF.

10
product categories
330
checkpoints in all
Free
on screen, PDF or email
Checklist · Apparel and textilesZ1.4 · Level II
Critical defectsBroken needle, needle fragment or other metal left in the garment
5
Major defectsHole, cut or tear; open, broken or skipped stitches on a seam
7
Minor defectsUntrimmed thread ends
6
6 on-site tests6 measurements7 packing checks
Ten categories · free

Pick a category. Get every checkpoint.

Inspection checklist

Apparel and textiles

T-shirts, shirts, dresses, knitwear, denim, outerwear, sportswear, childrenswear and fabrics by the metre.

Suggested planAQL 0 / 2.5 / 4.0ANSI/ASQ Z1.4, Level IISample size for your lot →
Supplier
Order / PO
Lot size
Date

Level II with AQL 0 / 2.5 / 4.0 suits most apparel. Premium lines often tighten major to 1.5.

Critical defectsAQL 0: none allowed

Major defectsAQL 2.5 typical

Minor defectsAQL 4.0 typical

On-site tests

Measurements unit: cm

PointHowReading
Chest width1 cm below the armhole, laid flat
Body lengthFrom the high point shoulder
Sleeve lengthShoulder point to cuff edge
Waist and hipRelaxed, laid flat
InseamCrotch point to hem (trousers)
Neck openingStretched and relaxed, knits

At least five units per size or version, against your specification and tolerances.

Packing and labelling

Market marks

EU
Fibre composition with the names in Regulation (EU) 1007/2011; care symbols to ISO 3758 are standard practice.
UK
Fibre composition under the Textile Products (Labelling and Fibre Composition) Regulations 2012.
US
Fibre content, country of origin and maker identity (name or RN) under the Textile Act; permanent care label under the FTC Care Labeling Rule.
Australia
Permanent care label under the care labelling information standard.
Children’s wear
Cords and drawstrings: EN 14682 in the EU and UK; 16 CFR 1120 in the US.

Your compliance team or test lab confirms which rules apply to your exact product.

How we inspect it. We check the order is finished and at least 80% packed, draw cartons at random, then inspect every garment in the sample on a lit table against the approved sample and your size spec. Stress tests and measurements use separate units so the sample stays saleable.

SourceSquid · sourcesquid.co/quality/checkpoints/apparel-and-textiles/ · Your specification and approved sample decide the final class of any defect.

Book the inspection

This checklist, run at the factory.

Our own inspectors in India and China work through the checklist on a random sample drawn to ANSI/ASQ Z1.4, with a photo report within 24 hours.

  • from USD 249 per person-day, travel included within main clusters Pre-shipment, in-line or loading inspection

    A principal tailors this checklist to your specification and golden sample, included in the booking, and confirms the inspector and the date.

You see the exact total before you confirm. Pay by card, or ask for an invoice. Outside the main clusters, travel is confirmed before you pay.

Checklist questions

Straight answers.

Anything else, ask us directly. A principal replies, not a bot.

[email protected]

What should a pre-shipment inspection checklist include?

The defects to look for, each classed as critical, major or minor; the on-site tests; the measurement points and tolerances; packing, labelling and carton checks; and the marks your market requires. Add your own specification and approved sample, which decide the final class of any defect.

Can I use this checklist with my own inspector or the factory’s QC?

Yes. Save it as a PDF and send it with your specification and golden sample photos. It works as a common list for anyone checking the goods.

Which AQL should I use?

Most consumer goods use ANSI/ASQ Z1.4 General Inspection Level II with AQL 0 for critical, 2.5 for major and 4.0 for minor defects. Each category below shows the usual plan; the AQL sampling planner gives the sample size for your lot.

Can you tailor the checklist to my product?

Yes. When you book an inspection, a principal tailors the checklist to your specification and golden sample at no extra charge, and agrees it with you before the inspector arrives.

How much does an inspection cost?

Inspections start at USD 249 per person-day, with travel included within our main clusters in India and China. You see the exact total before you confirm.

Chat on WhatsApp+91 98406 98791