Inspection checklist Apparel and textiles
T-shirts, shirts, dresses, knitwear, denim, outerwear, sportswear, childrenswear and fabrics by the metre.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 suits most apparel. Premium lines often tighten major to 1.5.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: cm
| Point | How | Reading |
|---|
| Chest width | 1 cm below the armhole, laid flat | |
|---|
| Body length | From the high point shoulder | |
|---|
| Sleeve length | Shoulder point to cuff edge | |
|---|
| Waist and hip | Relaxed, laid flat | |
|---|
| Inseam | Crotch point to hem (trousers) | |
|---|
| Neck opening | Stretched and relaxed, knits | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- Fibre composition with the names in Regulation (EU) 1007/2011; care symbols to ISO 3758 are standard practice.
- UK
- Fibre composition under the Textile Products (Labelling and Fibre Composition) Regulations 2012.
- US
- Fibre content, country of origin and maker identity (name or RN) under the Textile Act; permanent care label under the FTC Care Labeling Rule.
- Australia
- Permanent care label under the care labelling information standard.
- Children’s wear
- Cords and drawstrings: EN 14682 in the EU and UK; 16 CFR 1120 in the US.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We check the order is finished and at least 80% packed, draw cartons at random, then inspect every garment in the sample on a lit table against the approved sample and your size spec. Stress tests and measurements use separate units so the sample stays saleable.
SourceSquid · sourcesquid.co/quality/checkpoints/apparel-and-textiles/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Home textiles
Bed linen, duvets and pillows, towels, cushions, throws, curtains, table linen and rugs.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 is the usual starting point for home textiles.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: cm
| Point | How | Reading |
|---|
| Length and width | Laid flat without tension | |
|---|
| Pocket depth | Fitted sheets, at each corner | |
|---|
| Hem and border width | At several points per piece | |
|---|
| Flap depth | Pillowcases and duvet covers | |
|---|
| Pile height | Rugs and towels, where specified | |
|---|
| Weight per piece | Towels, throws and fillings (g) | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- Fibre composition under Regulation (EU) 1007/2011.
- UK
- Fibre composition under the Textile Products (Labelling and Fibre Composition) Regulations 2012.
- US
- Fibre content, country of origin and maker identity under the Textile Act; stuffed-article law labels where state rules require them.
- Australia
- Permanent care label under the care labelling information standard.
- Eco claims
- OEKO-TEX or organic labels only where a valid certificate covers the product.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We count sets and cartons, then open sampled units fully: sheets are unfolded and measured, towels weighed, covers zipped and unzipped, rugs unrolled on a clean floor. Colour is compared with the approved sample in a light box.
SourceSquid · sourcesquid.co/quality/checkpoints/home-textiles/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Kitchenware and drinkware, hardware and fittings, tools, fasteners, brackets, castings and sheet-metal parts.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 is typical. Engineering parts often add a separate plan for critical dimensions.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Overall length, width, height | Calipers or tape against the drawing | |
|---|
| Diameter | Outer and inner, at the points on the drawing | |
|---|
| Wall or sheet thickness | Micrometer or ultrasonic gauge | |
|---|
| Hole size and position | Pin gauges and calipers | |
|---|
| Flatness or straightness | Feeler gauge on a surface plate, where specified | |
|---|
| Weight | Scale, in grams | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- Food-contact items: glass-and-fork symbol or “for food contact” wording where food use is not obvious (Regulation (EC) 1935/2004).
- EU and UK
- Nickel release limits for parts in direct and prolonged skin contact (REACH Annex XVII, entry 27).
- EU (CBAM)
- Iron, steel and aluminium goods need emissions data from the producer for the importer’s CBAM declaration.
- US
- Country of origin marked on the article or its container; California Proposition 65 warning where a listed substance is present.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We inspect in good light against the golden sample, run the XRF and gauge checks on units drawn from different cartons, and photograph every defect next to a scale rule. Leak and function tests run on a separate set of units.
SourceSquid · sourcesquid.co/quality/checkpoints/metal-hardgoods/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Plastic products
Housings and covers, food containers and kitchenware, bottles, garden and household products, and technical parts.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 suits most consumer plastics. Technical parts add a dimensional plan per cavity.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Overall length, width, height | Calipers against the drawing | |
|---|
| Wall thickness | At the points on the drawing | |
|---|
| Critical fit dimension | Per cavity, where the mould has several | |
|---|
| Thread or neck finish | Gauges for bottles and closures | |
|---|
| Flatness or warp | Feeler gauge on a surface plate | |
|---|
| Weight | Scale, in grams | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- Food-contact plastics: written declaration of compliance and migration testing under Regulation (EU) 10/2011.
- EU and UK
- REACH: suppliers must inform you if an article contains a candidate-list substance above 0.1% by weight.
- Material mark
- Material code to ISO 11469 (for example >PP<) or a resin identification code, as specified.
- US
- Food-contact resins that meet FDA rules (21 CFR 174–178); Proposition 65 warning where a listed substance is present.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We note the mould and cavity numbers, draw samples across cartons so every cavity is represented, and inspect under good light at arm’s length. Colour is judged in a light box, and fit and seal tests run on separate units.
SourceSquid · sourcesquid.co/quality/checkpoints/plastic-products/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Electronics and electricals
Small appliances, chargers and power supplies, lighting, audio, wearables, battery-powered devices and accessories.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 is common. Safety tests often run on every sampled unit or a special-level plan.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Overall length, width, height | Calipers against the specification | |
|---|
| Cable length | Plug to product, in metres | |
|---|
| Plug pin dimensions | Where the plug is part of the product | |
|---|
| Button travel and fit | Against the golden sample | |
|---|
| Weight | Scale, in grams | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- CE marking with a Declaration of Conformity covering LVD, EMC, RoHS and RED as applicable; crossed-out wheelie bin (WEEE).
- UK
- UKCA or CE as the UK rules allow; WEEE mark.
- US
- FCC Part 15 authorisation for devices with digital or radio circuits; NRTL listing (such as UL or ETL) where your retailer requires it.
- Australia and NZ
- RCM mark, with registration on the EESS database for in-scope electrical equipment.
- Plugs
- BS 1363 (UK), CEE 7 (EU), NEMA 1-15 or 5-15 (US), AS/NZS 3112 (Australia and NZ).
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We bring calibrated hi-pot and earth testers, run the safety tests first, then the full function test, then the cosmetic check. One unit is opened and compared with the approved construction so component changes are caught early.
SourceSquid · sourcesquid.co/quality/checkpoints/electronics/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Furniture
Case goods and storage, tables, dining and upholstered seating, office chairs, outdoor furniture and flat-pack.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 is usual. For large items, many buyers use a special level to keep the sample practical.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Width, depth, height | Overall, against the drawing | |
|---|
| Seat or top height | From the floor | |
|---|
| Diagonals | Squareness of frames and carcasses | |
|---|
| Drawer inner size | Width, depth and height | |
|---|
| Level | All feet touch a flat floor | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- US
- STURDY Act stability and warning label for clothing storage units; TSCA Title VI label for composite wood; TB 117-2013 label for upholstered furniture sold in California.
- UK
- Display and permanent labels for upholstered furniture under the Furniture and Furnishings (Fire) (Safety) Regulations 1988.
- EU
- Wood furniture falls under the EUDR, which applies from 30 December 2026 for large and medium operators.
- Standards
- Test reports to the standards in your specification, for example EN 12520, EN 14749 or BIFMA.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We open cartons from different pallets, run a full trial assembly with the packed hardware, and inspect every surface in good light. Moisture readings, load and stability checks run on assembled units, which we photograph from every side.
SourceSquid · sourcesquid.co/quality/checkpoints/furniture/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Bags, wallets and small leather goods, belts, gloves, and leather, textile and synthetic footwear.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 is usual. Luxury lines often tighten major to 1.5.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Length, width, height | Bags and small leather goods | |
|---|
| Handle drop and strap length | Adjustable straps at both ends | |
|---|
| Leather thickness | Thickness gauge at several panels | |
|---|
| Insole length | Footwear, per size | |
|---|
| Heel and shaft height | Footwear, per size | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU and UK
- Footwear material labels for upper, lining and outer sole (Directive 94/11/EC).
- EU and UK
- Chromium VI in leather in contact with skin below 3 mg/kg (REACH Annex XVII, entry 47); azo dye limits (entry 43).
- US
- Country of origin marking; leather claims that follow the FTC leather guides (16 CFR 24); Proposition 65 warning where required.
- Care
- Care instructions where supplied match the material.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We inspect each sampled piece on a clean, lit table, checking every panel, seam and edge against the approved sample and the agreed leather grade. Shoes are checked as pairs, flexed and measured per size.
SourceSquid · sourcesquid.co/quality/checkpoints/leather-goods-and-footwear/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Ceramics and glass
Stoneware, porcelain and earthenware tableware, mugs, bakeware, vases and decorative pieces, and glassware.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 is usual. Sets are counted as one unit or per piece, as you prefer.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Height and diameter | Calipers at rim and base | |
|---|
| Capacity | Water fill, in ml | |
|---|
| Wall thickness | At the rim and body | |
|---|
| Lid fit gap | Feeler gauge where specified | |
|---|
| Weight | Scale, in grams | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- Lead and cadmium release limits for food-contact ceramics (Directive 84/500/EEC); glass-and-fork symbol where food use is not obvious.
- US
- FDA limits on lead in ceramicware; decorative ware that looks like tableware marked “Not for food use” (21 CFR 109.16); Proposition 65 in California.
- Claims
- Dishwasher, microwave and oven-safe marks match the test evidence.
- Backstamp
- Backstamp or marking as specified.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We unpack sampled cartons fully, ring-test every sampled piece, and inspect glaze and decoration under good light. Capacity, thermal shock and rock tests run on separate pieces, and a packed carton is drop-tested before loading.
SourceSquid · sourcesquid.co/quality/checkpoints/ceramics-and-glass/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Toys
Plush and soft toys, plastic and wooden toys, battery-operated and ride-on toys, games and puzzles, and baby toys.
- Supplier
- Order / PO
- Lot size
- Date
Toy buyers often use AQL 0 / 1.5 / 4.0 at Level II, with safety checks on extra units.
Critical defectsAQL 0: none allowed
Major defectsAQL 1.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Overall length, width, height | Against the specification | |
|---|
| Cord or string length | Fully extended | |
|---|
| Smallest detachable part | Before and after abuse tests | |
|---|
| Openings and gaps | Where fingers could enter | |
|---|
| Weight | Scale, in grams | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- CE mark, EN 71 series, warnings in local languages, manufacturer and importer details, and a type or batch number.
- UK
- UKCA or CE mark, with the UK importer’s details.
- US
- ASTM F963 and CPSIA testing, a Children’s Product Certificate, CPSIA tracking label and small parts warning where required (16 CFR 1500.19).
- Australia
- Mandatory standards for toys for children up to 36 months and for products containing button or coin batteries.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We run the safety checks on units separate from the visual sample so every result is clear. Our inspectors carry a small parts cylinder, torque and tension gauges and edge and point testers, and repeat the checks after the drop and abuse tests.
SourceSquid · sourcesquid.co/quality/checkpoints/toys/ · Your specification and approved sample decide the final class of any defect.
Inspection checklist Packaging
Corrugated shipping cartons, folding cartons, rigid gift boxes, labels and sleeves, mailers, bags and inserts.
- Supplier
- Order / PO
- Lot size
- Date
Level II with AQL 0 / 2.5 / 4.0 is usual; count packaging by the piece.
Critical defectsAQL 0: none allowed
Major defectsAQL 2.5 typical
Minor defectsAQL 4.0 typical
Measurements unit: mm
| Point | How | Reading |
|---|
| Internal length, width, height | Against the dieline | |
|---|
| Board caliper | Thickness gauge | |
|---|
| Print position | Distance of key elements from edges | |
|---|
| Label size | Labels and sleeves | |
|---|
At least five units per size or version, against your specification and tolerances.
Market marks
- EU
- PPWR applies from 12 August 2026: EU declaration of conformity and technical documentation, the importer’s name and postal address on the packaging, and lead, cadmium, mercury and hexavalent chromium together below 100 mg/kg.
- EU food contact
- From 12 August 2026, PFAS limits apply to food-contact packaging under PPWR.
- EU (later)
- Harmonised sorting labels become mandatory from 12 August 2028 at the earliest.
- FSC
- FSC label printed only where the supplier holds a valid licence and chain-of-custody certificate.
Your compliance team or test lab confirms which rules apply to your exact product.
How we inspect it. We compare sampled pieces with the approved proof and dieline under D65 light, measure board and dimensions, and test glue bonds and print. Where the packaging is new, we pack your product into it and run a drop test.
SourceSquid · sourcesquid.co/quality/checkpoints/packaging/ · Your specification and approved sample decide the final class of any defect.